The VDIV2:1 uses precision resistor networks to bring sensors with high output voltages into your data logger’s common mode range, allowing your data logger to measure the sensor. The VDIV2:1 divides the sensor’s signal voltage by a factor of two.
Read MoreThe VDIV2:1 contains two 10 kΩ resistors that have a ratio tolerance of ±0.02%. Increased input settling time may be necessary to accommodate the relatively high resistance of the voltage divider.
Used With | Sensors with a high voltage ouptut |
Division Ratio | 2:1 |
Resistance | 10 kΩ and 10 kΩ |
Tolerance | Ratio: ±0.02% (@ 25°C) |
额定功率 | 0.1 W (@ 70°C) per element |
Maximum Temperature Coefficient | Ratio: 2 ppm/°C (0° to 70°C) |
Dimensions | 1.5 x 1.5 x 2.7 cm (0.6 x 0.6 x 1.0 in.) for body with prongs |
Weight | 6 g (0.2 oz) |
Note:The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.
Product | Compatible | Note |
---|---|---|
21X(retired) | ||
CR10(retired) | ||
CR1000(retired) | ||
CR10X(retired) | ||
CR200X(retired) | ||
CR206X(retired) | ||
CR211X(retired) | ||
CR216X(retired) | ||
CR23X(retired) | ||
CR295X(retired) | ||
CR300 | ||
CR3000(retired) | ||
CR310 | ||
CR350 | ||
CR500(retired) | ||
CR5000(retired) | ||
CR510(retired) | ||
CR6 | ||
CR800 | ||
CR850 | ||
CR9000(retired) | Compatible CR9000 modules are the CR9050 and the CR9052; the CR9051 is partially compatible. | |
CR9000X(retired) | Compatible CR9000X modules are the CR9050 and the CR9052; the CR9051 is partially compatible. |
The VDIV2:1 uses two adjacent single-ended analog inputs (one differential channel); an adjacent analog ground channel accepts the "ground prong" of the VDIV2:1. Not all data logger terminal strips have this sequence on all channels, so please check your data logger's wiring panel to confirm channel assignments, especially if you plan to use multiple terminal input modules.
Please note that if a CR10X will be used to measure thermocouples in the same application, newer CR10X Wiring Panels and the CR10XTCR Reference Thermistor (with its accompanying thermocouple cover) are deep enough to cover the data logger input channels with a VDIV2:1 attached; older CR10TCRs are not deep enough.
The VDIV2:1 is measured with either the VoltSE or VoltDiff Instruction in CRBasic, and with Instruction 1 (SE Volts) or 2 (DiffVolts) in Edlog. Each VDIV2:1 can be wired to make one differential measurement or two single-ended measurements.
In this example program, a VDIV10:1 and the VoltDiff() instruction are used to measure an input voltage with a maximum voltage of 14 VDC, as described in the VDIV10.1/VDIV2.1 manual.
Number of FAQs related toVDIV2:1:3
Expand AllCollapse All
The CR1000 can measure analog voltages in the ±5 Vdc range. A voltage divider such as the VDIV2:1 is required to reduce 10 Vdc to an acceptable range.For examples of wiring and programs,see theVDIV10:1/VDIV2:1 manual.
These two voltage dividers can handle different maximum input voltages.
We've updated our privacy policy.Learn More