/ UT30.
UT30 30 FT万能塔with Adjustable Mast

Overview

The UT30 is a durable instrument tower that can be used for a variety of applications. The UT30 tower provides a sturdy mount for many meteorological monitoring applications—especially air quality stations and regional Mesonets, where the 9.14 m (30 ft) measurement height for wind sensors is standard. It also holds antennas, solar panels, environmental enclosures, radiation shields, and crossarms. It is a versatile instrument mount: many of the same sensor mounts that are used with either our tripods or other towers can be used with the UT30.

阅读更多

福利和特色

  • 坚固,长期仪器安装
  • 耐腐蚀

图片

UT30正视图
UT30正视图
UT30正视图
UT30后视图
UT30等距
UT30安装有测量设备(单独出售)

详细说明

UT30塔包括三个3米(10英尺)的部分,一个可伸展的桅杆和两个电缆系套件。可伸缩式桅杆具有1.5米(5英尺)的长度,外径3.175厘米(1.25英寸)[摇摆至2.5厘米(1英寸)]。

Top 3 m Section

The top section is constructed from 2.5 cm (1 in) OD aluminum tubing. Its width is 25.7 cm (10.1 in) on a side (center of tubing to center of tubing).

中心3 M部分

The center section is constructed from 2.5 cm (1 in) OD aluminum tubing. Its width is 33.3 cm (13.1 in) on a side (center of tubing to center of tubing).

底部3米

The bottom section is constructed from 3.175 cm (1.25 in) OD aluminum tubing. Its width is 43.2 cm (17 in) on a side (center of tubing to center of tubing).

Mounting Base, Grounding Kit, and Guying Kit
This tower requires a mounting base and grounding kit. Campbell Scientific also recommends guying the UT30 with our UTGUY Guy Kit. See Ordering Info on the web page for more information.

规格

Material Hardened drawn 6063-T832 aluminum
Guyed Tower Area Requirements 〜5米(17英尺)半径
Required Concrete Pad Dimensions 91 x 91 x 122 cm (36 x 36 x 48 in.) for B18 Concrete Mounting Base

混凝土垫要求呈现重土;光,移位或砂土需要更大的混凝土垫。
可伸展的桅杆
  • 1.5 m (5 ft) length
  • 3.175厘米(1.25英寸)外径(摇摆到2.5cm [1英寸]外径)
Pipe Outer Diameter
  • 2.5厘米(1.0英寸)的上部垂直管道
  • 用于下部的垂直管道3.18厘米(1.25英寸)
  • 交叉支撑/织带0.953厘米(0.375英寸)
横刀测量高度 10米(33英尺)
Height 10.1米(33英尺)
Shipping Dimensions 310 x 46 x 46 cm(122 x 18 x 18英寸)
Shipping Weight 29公斤(65磅)

Maximum Wind Load Recommendation

B18基础(无人机) 177 km / h(110英里/小时)
RFM18 Base (with UTGUY) 177 km / h(110英里/小时)
utbase(未经核武器) 177 km / h(110英里/小时)
-笔记- 风力负荷耐力受锚固和安装质量的影响;盖伊张力;土壤类型;男人角度;和编号,类型和定位在塔架上的仪器。

风力载荷推荐假设安装,适当的锚固,充足的土壤和总仪器投影面积小于0.19米2(2 ft2)。

For the RFM18 base, the wind load recommendation also assumes that the UTGUY’s turnbuckles are preloaded just enough to equalize tension and that the tower is guyed at a 60 degree angle relative to the ground (maximum).

兼容性

笔记:The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.

安装设备

产品 兼容的 笔记
019Alu(退休)
CM202
CM202SS.
CM203
CM204
CM204SS.
CM206
UT018-5.(退休)

Additional Compatibility Information

外壳括号

我们的环境外壳的“-TM”安装选项用于将我们的外壳连接到UT30塔。使用“-TM”选项订购的机箱将配备安装在机箱顶部的三件套支架和安装在机箱底部的相同的三件套支架。该安装支架选项使用与“-mm”选项相同的三件套括号,除了重新排列的碎片,使得法兰位于支架的侧面而不是中间。每个法兰的中心之间的距离需要为17“。

笔记:
带有“-TM”选项的机箱是为UT10塔配置的运送。UT30客户需要:(1)拆下将支架上的螺栓拆下到外壳,(2)滑出法兰部分,使每个法兰的中心之间的距离为17“,并且(3)将括号重新连接到括号外壳使用原始螺栓。

Videos & Tutorials

经常问的问题

与之相关的常见问题解答数量UT30.5.

Expand AllCollapse All

  1. The top section of the tower is made of 1" OD aluminum tubing; in cross-section, the topmost tower section is 10.1 inches on a side (center of tubing to center of tubing).

    塔的中间部分由1“OD铝管制成;在横截面中,侧面塔部分是13.1英寸(管道的管道中心)。

    塔架的底部由1.25“OD铝管制成;在横截面中,侧塔部分在一侧是17英寸(管道的中心,管道中心)。

  2. B18混凝土安装底座必须在浇筑混凝土基础之前附着在底塔部分。

  3. 在涉及塔的应用和强风或需要将大量齿轮附加到横梁的需要,Campbell Scientifics建议使用第二CM210横杆托架的更长的横梁。(每个CM202,C204或CM206横臂的一个cm210船舶。)将横梁固定到塔上的两个点,以向横梁增加稳定性和刚性。横梁可以在脚上移动(塔架上的垂直支撑件之间的距离),或者横梁可以在塔上居中。

  4. 塔的硬件,以及个人塔节ns, can be special ordered if necessary. Contact Campbell Scientific for assistance. If you would prefer to purchase the hardware at a local store, the items are listed below.

    • Nuts and bolts for the tower:
      • 3/8 in. hex cap
      • 2英寸长,镀锌
    • Nuts and bolts for the concrete mounting base:
      • 3/8 in. hex cap
      • 2½英寸长,镀锌
  5. Individual tower sections, as well as tower hardware, can be special ordered if necessary. Contact Campbell Scientific for assistance.

Case Studies

西德克萨斯州梅内斯特
West Texas Mesonet
The West Texas Mesonet (WTM) project was initiated by Texas Tech University in 1999 to......read more

隐私政策更新

我们更新了我们的隐私政策。Learn More

Baidu