RF422 868 MHz SRD860 Radio

Overview

The RF422 is an 868 MHz SRD860 radio designed to provide license-free operation for wireless serial communications in Europe. The RF422 transmits data at 10 kbps with a maximum power of 25 mW, and it employs listen-before-talk (LBT) and adaptive-frequency-agility (AFA) to provide a robust link of up to 5 km (line-of-sight). The RF422 supports point-to-point and point-to-multipoint data logger communications and PakBus repeater operation.

The RF422 is part of the RF407 series of radios that includes:

  • RF407: North America (FCC & IC), 902 to 928 MHz
  • RF412: Australia (ACMA RCM), 915 to 928 MHz
  • RF422: Most of Europe and some of Asia (ETSI), 863 to 870 MHz
  • RF427: Brazil (ANATEL), 905/920 MHz

Read More

Benefits and Features

  • Does not require individual operational license in Europe
  • Robust serial communication, optimized for PakBus networks
  • Low power (< 2 mA idle) during periods of inactivity
  • Supports point-to-point with RF retries and point-to-multipoint operations
  • Remote diagnostics using PakBus node operations
  • Operational power can be supplied over USB when attached to PC

Campbell Scientific recommends installing the RF422 868 MHz radio at least 200 m (656.2 ft) from any 4G LTE cellular transmitter, including towers and cellular modems/gateways.

Images

Front tilt view
Front tilt view
Front tilt view
Front view
后视图
Left view
Right view
Top view
Bottom view

Detailed Description

System Components

An RF422 radio needs to be at both the base station and field site. Each radio requires an antenna that does not exceed 2.1 dBi in gain over the 863 to 870 MHz frequency range, such as the 28767 whip antenna offered by Campbell Scientific.The RF422 has a reverse polarity SMA (RPSMA) connector for attaching the antenna or antenna cable.

Powering the Radio

At the base station, the radio typically uses ac power that is either supplied by the 15966 wall charger or through the PC via the USB port and cable. At the field site, the radio is typically powered by the data logger through the CS I/O port. The 14291 Field Cable can also be used to connect the radio to an appropriate 12 Vdc power supply. This field cable is required when the radio is connected to the data logger’s RS-232 port instead of the CS I/O port.

Specifications

Radio Type SRD860, LBT+AFA
Restrictions See REC70-03E, CEPT recommendation on the use of SRD.
Compliance Listen before talk (LBT) and automatic frequency agility (AFA) to comply with ETSI duty cycle requirements. Radio communication effective duty cycle = (number of channels * 100) / 3600.
Channel Capacity 30 channels (default), software configurable for the purpose of meeting local regulations; 10 sequences for reducing interference through channel hop.
Frequency 863 to 870 MHz
Country Used In EMEA (Europe, Middle East, and Africa)
Transmission Distance
  • -Note- Transmission distance assumes line-of-sight and appropriate antenna. Line-of-sight obstructions, RF interference, and antenna type will affect transmission distance.
  • Up to 5 km (3.11 mi) depending on antenna and line-of-sight
Power Output 2 to 25 mW (software-selectable; assuming 2 dBi antenna gain)
Receiver Sensitivity -106 dBm
RF Data Rate 10 kbps
Link Throughput 8 kbps
Antenna Connector Reverse Polarity SMA (RPSMA) jack
LEDs Red TX/PWR and green RX
RS-232 Baud Rate 1200 to 115200 bps
CS I/O Modes SDC 7, 8, 10, 11, and ME master
Power 9 to 16 Vdc
Power Connector 2.5 mm dc power jack
Operating Temperature Range -40° to +70°C
Certifications
  • CE
  • ETSI EN 300 220-2 V2.3.1
Average Current Drain
  • < 25 mA (transmit at 25 mW TX Power)
  • 15 mA (receive)
  • < 0.5 mA (standby, depending on power-saving mode)
Communication Ports
  • RS-232 9-pin D female
  • CS I/O 9-pin D male
  • USB Type B jack
Service Requirements Shares frequency with other devices. Must not cause harmful interference to licensed radios. Requires line-of-sight.
Dimensions 11.1 x 6.9 x 2.7 cm (4.4 x 2.7 x 1.1 in.)
Dimensions are from the tip of the antenna connector to the other side of the case, and from the bottom of the case to the top of the DB9 connector jack screw. The width includes the thickness of the screw heads on the screws that hold the case together.
Weight
  • 136 g (4.8 oz) without "Ships With" items
  • 283.5 g (10 oz) with "Ships With items

LBT+AFA Performance
Channel Spacing 100 kHz
Receiver Bandwidth 150 kHz
Modulation Bandwidth < 300 kHz
LBT Threshold < -88 dBm
TX on Time < 1 s

Compatibility

The RF422 is over-the-air compatible with other RF422-based products. The RF422 can only communicate wirelessly with other RF422 radios and other Campbell Scientific products that have the "-RF422" option.

Data Logger Considerations

Data Logger RS-232 CS I/O
CR200(X)
CR800/CR850
CR1000
CR3000
CR5000
CR9000(X)
CR300 *
CR6
CR510-PB
CR10X-PB
CR23X-PB
Mixed-array data loggers **

Notes:
*Use a 18663 null modem cable.
**It is possible to connect a mixed-array data logger (e.g., CR10, CR10X, CR23X, 21X, CR7) by using an SC932A or SC105 between the data logger's CS I/O port and the RF422's RS-232 port.

Videos & Tutorials

Articles and Press Releases

Privacy Policy Update

We've updated our privacy policy.Learn More

Baidu