退休›
This product is no longer available.
CWS900 900 MHz Configurable Wireless Sensor Interface
Services Available
Repair
校准
免费支持 Yes

Overview

The CWS900 allows a sensor with a special connector to be used in a wireless sensor network; the special connector is available as an option for a large variety of sensors. (See the Compatibility information on the web page.)

CWS900包含一个内部900 MHz传播广播,该广播电台将数据传输到CWB100无线基站或其他无线传感器。CWS900的内部收音机的频率在美国和加拿大通常使用。

Read More

好处和功能

  • Allows a wide variety of sensors to be used in a wireless network
  • Internal frequency-hopping, spread-spectrum radio provides longer range and less interference
  • Battery powered
  • 一个可靠的、低,低功耗的方法making measurements in applications where cabled sensors are impractical or otherwise undesirable
  • 传输可以通过多达三个无线传感器进行路由

该产品将于2017年4月10日停止。请审查CWS系列和CWB系列中断通知for further details.


Images

详细说明

CWS900具有密封的连接器,用于连接一个雨量,风传感器,温度/RH探头或其他低功率传感器。它测量模拟电压,低水平的交流电,脉冲计数,并可以提供激发电压,以供电某些传感器或进行桥梁测量。传感器执行的测量类型是使用无线传感器计划器,网络计划器或DevConfig软件配置的。CWS900与PC接口通过A205 CWS传感器到PC接口进行配置。

CWS900可以通过最多三个无线传感器路由其传输。数据记录器连接到CWB100基站,用于处理和存储CWS900的数据。

CWS900是使用碱性电池或可充电电池和太阳能电池电池供电的电池。

Why Wireless?

There are situations when it is desirable to make measurements in locations where the use of cabled sensors is problematic. Protecting cables by running them through conduit or burying them in trenches is time consuming, labor intensive, and sometimes not possible. Local fire codes may preclude the use of certain types of sensor cabling inside of buildings. In some applications measurements need to be made at distances where long cables decrease the quality of the measurement or are too expensive. There are also times when it is important to increase the number of measurements being made but the data logger does not have enough available channels left for attaching additional sensor cables.

不te:The internal radio is not designed to move a lot of data quickly. It takes 15 to 30 seconds per hop when moving data from a sensor, through a sensor used as a repeater, and ending up at the base radio. Going through three repeaters could take a data packet anywhere from 45 to 90 seconds to get to the base radio.

Specifications

天气抵抗 传感器和电池组的IP67等级(必须正确安装电池组。每个传感器都经过泄漏测试。)
Operating Temperature Range -25°至 +50°C
Operating Relative Humidity Range 0 to 100%
Power Source 2电池寿命为1年的AA电池,假设传感器样品每10分钟采集一次传感器。(可选的太阳能充电。)
Average Current Drain 300 μA (with 15-minute polling and depending on attached sensor)
Analog Channels
  • SE1,SE2,SE3(单端)
  • DF (differential)
模拟输入范围 -1至+2.5 VDC
解析度 0.3 μV
激发电压 2.5 V, 3.3 V, 5.0 V (20 mA maximum)
激发电压Accuracy ±2%(-35°至 +70°C)
Low-Level AC Input 20 mV minimum (10 kHz maximum frequency)
Temperature Accuracy ±0.2ºC
模拟测量精度
  • ±(0.02% of reading + 2 µV) (0° to 50°C)
  • ±(读取 + 2 µV的0.05%)(-35°至 + 70°C)
Bridge Measurement Accuracy (+2.5 V excitation only)
  • ±(0.03%的读数 + 3 µV)(0°至50°C)
  • ±(0.07% of reading + 3 µV) (-35° to +70°C) Not including sensor and measurement noise, and external bridge resistor errors.
Dimensions 15 x 6 x 4.5 cm (5.9 x 2.4 x 1.77 in.)
Weight 184 g (6.5 oz)

开关闭合

Maximum Count Rate 100 Hz
Minimum Open Time 5 ms
最小关闭时间 5 ms
最大弹跳时间 4 ms
Maximum Number of Counts Records 1,000,000 counts before it rolls over.

内部25 MW FHSS广播

Frequency 902至918 MHz
Where Used US and Canada
FHSS频道 50
Transmitter Power Output 25 mW (+14 dBm)
Receiver Sensitivity -110 dBm (0.1% frame error rate)
Standby Typical Current Drain 3μA
接收典型的电流排水 18 MA(全奔跑)
传输典型电流流量 45 MA
平均操作电流 15 μA (with 1-second access time)
Quality of Service Management RSSI
附加的功能 GFSK modulation, data interleaving, forward error correction, data scrambling, RSSI reporting

Compatibility

不te:以下显示了显着的兼容性信息。这不是所有兼容或不兼容产品的全面列表。

Data Loggers

Product Compatible 不te
CR1000(retired)
CR200X(retired)
CR206X(retired)
CR211X(retired)
CR216X(retired)
CR295X(retired)
CR3000(retired)
CR6
CR800
CR850
CR9000X(retired)

Sensors

Product Compatible 不te
014A-L
03002-L 使用-CWS选项
034b-l 使用-CWS选项
05103-45-L(retired) 使用-CWS选项
05103-L 使用-CWS选项
05106-L(retired) 使用-CWS选项
05305-L 使用-CWS选项
107
108
109 使用-CWS选项
109SS-L 使用-CWS选项
110PV-L(retired) 使用-CWS选项
27106T-L
43347-L
52202-L
CMP11-L 使用-CWS选项
CMP21-L
CMP6-L 使用-CWS选项
CS215-L(retired)
CS300-L(retired) 使用-CWS选项
CS511-L 使用-CWS选项
CS526-L
CS547A-L
CS700H-L
CS700-L
CSAT3(retired)
CSIM11-L
CSIM11-ORP-L
HC2S3-L(retired) 使用-CWS选项
HMP155A-L
HMP60-L 使用-CWS选项
LI190SB-L(retired) 使用-CWS选项
LI200S-L(retired) 使用-CWS选项
LI200X-L(retired)
OBS-3+(retired)
OBS300(retired)
OBS500(retired)
TB4-L 使用-CWS选项
TB4MM-L 使用-CWS选项
TE525-L 使用-CWS选项
TE525mm-L 使用-CWS选项
TE525WS-L 使用-CWS选项
WINDSONIC-L(retired)

其他兼容性信息

数据记录器的注意事项

Compatible Data Logger Operating Systems
  • CR800-Series: CR800.Std.21 and higher
  • CR1000:CR1000.STD.21及更高
  • CR3000:CR3000.STD.21及更高
  • CR6:版本4.0及更高版本

Sensors

One sensor can be connected to the CWS900. Sensors with the -CWS option will include a connector that mates with the CWS900. Alternatively, a sensor can connect with the CWS900 via the A150 Desiccant Case.

A150 Desiccated Case

A150干燥的情况具有-CWS电缆终止选项。它允许我们的CS451和CS456压力传感器或其他具有通风电缆连接到CWS900的传感器。测量模拟电压,频率和脉冲的传感器也可以使用A150与CWS900连接。

下载

CWS900 Firmware v.5 (448 KB)03-30-2016

CWS900的最新固件。

查看更新历史记录

Wireless Sensor Planner v.1.7 (30.5 MB)08-08-2013

无线传感器计划器是与坎贝尔科学无线传感器一起使用的工具。它有助于设计和配置无线传感器网络。

常见问题

Number of FAQs related toCWS900:6

Expand All全部收缩

  1. 需要A205来将无线基站的无线电地址写给无线传感器固件,以便传感器可以响应基本站的投票。这是使用设备配置实用程序软件完成的。A205对于直接将计算机连接到CWS655,CWS220或CWS900,用于诊断,更改基站无线电地址,上传新固件并验证传感器功能。仅需购买一个A205,除非具有多台计算机的多个用户需要执行这些任务。

  2. 由于设备和收音机使用相同的频带,因此会有干扰。影响干扰量的因素包括通信无线电和CWS无线电之间的距离,以及CWS基础与传感器之间的距离。同样,是否会设置通信收音机作为主人,从而影响了干扰量。

  3. To incorporate a sensor that is compatible with wireless sensor interfaces into a wireless network, a CWS900-series wireless sensor interface is needed, as well as an A205 CWS-to-PC interface to configure it.


Articles and Press Releases

隐私政策更新

We've updated our privacy policy.Learn More

Baidu