CS511由Sensorex制造,是一种可潜水,坚固,低维护的传感器,将溶解氧气溶于培养基(通常是水)。它由一个自偏的电池组成,该电池产生与测量培养基(通常是水)中存在的氧气量成比例的毫伏信号。
Read MoreThe "-L" on a product model indicates that the cable length is specified at the time of order.
Oxygen diffuses through the CS511’s membrane onto a cathode that produces a chemical reaction. An electrical current is produced by this reaction, which is converted from microamps to millivolts by an in-line resistor. An in-line thermistor provides automatic temperature compensation.
由于CS511干燥,因此需要在使用传感器之前添加DO电解质。传感器的运输套件中包括电解质和备用膜。
目前,CS511是Sensorex的型号DO6400/t。在2008年6月之前,CS511是Sensorex的型号DO6200/t。对于这两个传感器,编程,接线和大多数规格都是相同的。但是,他们使用不同的配件并看起来不同。更旧的DO6200/T可用。(请参阅订购信息在网页上。)
有关旧DO6200/T的图像,请参阅retired version of the CS511 manual。有关更多信息,请联系Campbell Scientific。
Operating Temperature Range | 0° to 50°C |
测量范围 | 0.5 to 50 ppm (for O2) |
准确性 | ±2% |
Output | 33 mV±9 mV(饱和100%);<2 mV(0%饱和度) |
响应时间 | 5 min from 100% to 0% oxygen |
Minimum Water Velocity | 5 cm s-1(2英寸-1) across membrane |
最低浸入深度 | 6.35厘米(2.5英寸) |
压力 | 0 to 100 psig |
Temperature Compensation | 从4°到40°C的自动变量 |
探针电解质 | NaCl + glycerol (prevents freezing) |
直径 | 5.72 cm (2.25 in.) |
高度 | 从传感器底部到电缆应变末端的17.78厘米(7英寸) |
Shipping Weight | 0.8千克(1.75磅),包括传感器和运输套件 |
Note:以下显示了显着的兼容性信息。这不是所有兼容或不兼容产品的全面列表。
Product | Compatible | Note |
---|---|---|
CR1000(retired) | ||
CR1000X | ||
CR200X(retired) | ||
CR206X(retired) | ||
CR211X(retired) | ||
CR216X(retired) | ||
CR295X(retired) | ||
CR300 | ||
CR3000(retired) | ||
CR310 | ||
CR350 | ||
CR5000(retired) | ||
CR6 | ||
CR800 | ||
CR850 | ||
CR9000(retired) | ||
CR9000X(retired) |
由于CS511干燥,因此需要在使用传感器之前添加DO电解质。传感器的运输套件中包括电解质和备用膜。
在水速度小于每秒2.5厘米(1英寸)的应用中,提供了PT4搅拌器-1). It sweeps a brush across the sensor membrane to keep the sensor clean and provide water movement for accurate readings.
Number of FAQs related toCS511-L:10
展开全部全部收缩
A standard reference table for dissolved oxygen in water/temperature/elevation is included.
否。电缆连接到内部电子设备。删除它们将违反保修。
是的。该探测完全可潜水。
一般来说,每年两到三次。然而,如果the membrane gets damaged, clean it accordingly.
If the probe will be shelved for a month or more, the electrode should be removed. When the sensor will be used again, use fresh electrolyte and a new membrane. Following these guidelines will enable the probe to be stored indefinitely.
CS511-L是一种旨在在水中起作用的电溶解氧探针。如o2通过半透明的膜,氧与探针中的电解质溶液反应。随着更多的氧气可用,会发生电化学过程,以便记录MV输出的增加。氧气的来源可以通过空气,水或液体浆液。土壤不是很均匀,因此溶解的氧气无法自由移动。
Most Campbell Scientific sensors are available as an –L, which indicates a user-specified cable length. If a sensor is listed as an –LX model (where “X” is some other character), that sensor’s cable has a user-specified length, but it terminates with a specific connector for a unique system:
If a sensor does not have an –L or other –LX designation after the main model number, the sensor has a set cable length. The cable length is listed at the end of the Description field in the product’s Ordering information. For example, the 034B-ET model has a description of “Met One Wind Set for ET Station, 67 inch Cable.” Products with a set cable length terminate, as a default, with pigtails.
如果电缆用特殊的连接器终止于唯一系统,则型号的末端指定了哪个系统。例如,034B-ET模型将传感器指定为ET107系统的034B。
并非每个传感器都有不同的电缆终止选项。可以通过在传感器产品页面的订购信息区域的两个地方查看特定传感器的选项:
如果在–ET,–ETM,–LC,–LQ或–QD版本中提供传感器,则该选项的可用性反映在传感器型号中。例如,034b以034b-et,034b-etm,034b-lc,034b-LQ和034b-qD提供。
如果有的话,所有其他电缆终止选项均在传感器产品页面的“电缆终止选项”下的“订购信息”页面上列出。例如,如034B-L产品页面的订购信息区域所示,使用–CWS,–PT和–PW选项提供034B-L风集。
Note:As newer products are added to our inventory, typically, we will list multiple cable termination options under a single sensor model rather than creating multiple model numbers. For example, the HC2S3-L has a –C cable termination option for connecting it to a CS110 instead of offering an HC2S3-LC model.
Many Campbell Scientific sensors are available with different cable termination options. These options include the following:
Note:The availability of cable termination options varies by sensor. For example, sensors may have none, two, or several options to choose from. If a desired option is not listed for a specific sensor, contact Campbell Scientific for assistance.
To incorporate a sensor that is compatible with wireless sensor interfaces into a wireless network, a CWS900-series wireless sensor interface is needed, as well as an A205 CWS-to-PC interface to configure it.
We've updated our privacy policy.Learn More