CS11-L AC Current Sensor
Measure the ac Current along an Electrical Wire
weather applications water applications energy applications gas flux and turbulence applications infrastructure applications soil applications

Overview

说他们检测和测量交流电流an electrical wire using the magnetic field that is generated by that current. The sensor outputs a millivolt signal allowing it to be directly connected to our data loggers.

Read More

Benefits and Features

  • Ideal applications include motor or generator load conditions, efficiency studies, intermittent fault detection, and rough submetering
  • Sensor is external to the wire jacket and has no direct electrical connection to the system

Images

Top view
Top view
Top view
Bottom view

Detailed Description

The CS11 uses CR Magnetic's CR8459 Current Transformer to detect the ac current along an electrical wire using the magnetic field that is generated by that current. The CS11 is external to the wire jacket and has no direct electrical connection to the system.

The CS11 is recommended for measurements that do not require high accuracy, such as motor or generator load condition monitoring, efficiency studies, intermittent fault detection, and rough submetering.

Specifications

Measurement Range 0.15 to 200 A (0.15 to 125 A for CR200X)
Frequency 50 and 60 Hz
Insulation Resistance 100 MΩ (@ 500 Vdc)
High Potential 2000 V
Rated Current 200 A, 125 A (CR200X)
Accuracy Typically ±1% of actual value with provided multiplier (with 10 Ω maximum burden [resistive])
Multiplier iMult=200 A/1000 mV=0.2
Operating Temperature Range -25° to +55°C
Storage Temperature Range -25° to +70°C
Case Material Polypropylene resin
Construction Epoxy encapsulated
Inner Diameter 1.9 cm (0.75 in.)
Outer Diameter 4.8 cm (1.89 in.)
Height 1.7 cm (0.67 in.)

Compatibility

Note:The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.

Data Loggers

Product Compatible Note
21X(retired)
CR10(retired)
CR1000(retired)
CR1000X
CR10X(retired)
CR200X(retired)
CR206X(retired)
CR211X(retired)
CR216X(retired)
CR23X(retired)
CR295X(retired)
CR300
CR3000(retired)
CR310
CR350
CR500(retired)
CR5000(retired)
CR510(retired)
CR6
CR800
CR850
CR9000(retired)
CR9000X(retired)

Frequently Asked Questions

Number of FAQs related toCS11-L:5

Expand AllCollapse All

  1. Connect the red wire to ground rather than its normal location on the CR200(X).

  2. The following are some of the features of the CS11-L:

    • The quality of the measurements was improved by upgrading the 10 ohm internal resistor.
    • The CS11-L is compatible with the CR200(X)-series dataloggers, as well as all of the data loggers that were compatible with the CS10-L. This allows the CS11-L to replace both the CS10-L and the CS15-L.
    • The programming examples were improved to give greater stability to the measurements. On some data logger models, theACPower()instruction can be used.
  3. Not directly. If the CS11-L is connected to a data logger, the data logger can take the ac measurement and control a solid-state relay based on some threshold within the data logger program. The solid-state relay can then control other relays, solenoids, or motor starters. (Use of a solid-state relay is preferred because the data logger can trigger it with a small 5 Vdc mA signal.)

  4. Yes. Three CS11-L sensors can be connected to a data logger to measure the amperage on each of three phases.

  5. No. The CS11-L is an ac-only sensor.


Articles and Press Releases


This Product Replaced

Privacy Policy Update

We've updated our privacy policy.Learn More

Baidu