This product is no longer available and has been replaced by:CNR4-L.
| Services Available | |
|---|---|
| Repair | No |
| Free Support | No |
Overview
The CNR1 net radiometer by Kipp & Zonen is for applications requiring research-grade performance. The radiometer measures the energy balance between incoming short-wave and long-wave IR radiation versus surface-reflected short-wave and outgoing long-wave IR radiation. The CNR1 consists of a pyranometer and pyrgeometer pair that faces upward and a complementary pair that faces downward. The pyranometers and pyrgeometers measure short-wave and far infrared radiation, respectively. The CNR1 also includes an RTD to measure the radiometer’s internal temperature and a heater that can be used to prevent condensation. Lead length is 82 ft. For custom cable length, order CNR1-L.
If you need a mounting bracket for a CNR1 or CNR1-L, get advice by clicking theAsk a Questionbutton on this page, or call 435-227-9000 and ask to speak to someone in our Flux group.
Read MoreImages
Detailed Description
The CNR1 comes with an 82-ft cable length. This net radiometer is for applications requiring research-grade performance. It measures the energy balance between incoming short-wave and long-wave infrared radiation versus surface-reflected short-wave and outgoing long-wave infrared radiation.
The CNR1 consists of a pyranometer and pyrgeometer pair that faces upward and a complementary pair that faces downward. The pyranometers and pyrgeometers measure short-wave and far infrared radiation, respectively. All four sensors are calibrated to an identical sensitivity coefficient.
CNR1还包括一个RTD测量收音机meter’s internal temperature, a 4WPB100 module to interface the RTD with the data logger, and a heater that can be used to prevent condensation.
The CNR1 uses six differential or four single-ended and two differential analog channels on the data logger. Data loggers that provide sufficient channels include our CR1000, CR3000, and CR5000.
If you need a mounting bracket for a CNR1 or CNR1-L, get advice by clicking theAsk a Questionbutton, or call 435-227-9000 and ask for someone in our Flux group.
Specifications
| Sensors | Kipp & Zonen’s CM3 ISO-class, thermopile pyranometer, CG3 pyrgeometer, PT100 RTD |
| Pyranometer Spectral Response | 305 to 2800 nm |
| Pyrgeometer Spectral Response | 5000 to 50,000 nm |
| Response Time | 18 s |
| Sensitivity Range | 7 to 15 μV W-1m2 |
| Pyranometer Output Range | 0 to 25 mV |
| Pyrgeometer Output Range | ±5 mV |
| Expected Accuracy for Daily Totals | ±10% |
| Directional Error | < 25 W m-2(pyranometer) |
| Heating Resistor | 24 ohm, 6 W (at 12 Vdc) |
| CE Compliance | CE compliant under the European Union’s EMC directive |
Compatibility
Note:The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.
Data Loggers
| Product | Compatible | Note |
|---|---|---|
| 21X(retired) | ||
| CR10(retired) | ||
| CR1000(retired) | ||
| CR10X(retired) | ||
| CR200X(retired) | ||
| CR206X(retired) | ||
| CR211X(retired) | ||
| CR216X(retired) | ||
| CR23X(retired) | ||
| CR295X(retired) | ||
| CR3000(retired) | ||
| CR500(retired) | ||
| CR5000(retired) | ||
| CR510(retired) | ||
| CR800 | ||
| CR850 | ||
| CR9000(retired) | ||
| CR9000X(retired) |
Additional Compatibility Information
Do Not use the UT018 crossarm with the 14364 mounting bracket to fasten the CNR1 to a tower leg. The 14264 mounting bracket should be attached directly to a verticle pole.
Data Logger Considerations
The CNR1 uses six differential or four single-ended and two differential analog channels on the data logger.
Documents
Brochures
Manuals
经常问什么estions
Number of FAQs related toCNR1:3
Expand AllCollapse All
-
As a general guide, go at least 1.5 m above the tallest plant (tree) in an ecosystem.
-
If the BR (Bowen Ratio) system is being run on 21X or CR23X dataloggers, a CNR1 net radiometer cannot be used with the system because those data loggers do not have enough input channels. For this reason, Campbell Scientific recommends running a CNR1 out of a separate data logger.
-
CNR1 is a four-output net radiometer. It gives values for incoming short-wave, incoming long-wave, outgoing short-wave, and outgoing long-wave radiation. It also calculates the net radiation and albedo.
Case Studies
The Geography Department at Bucknell University has implemented a weather station to obtain meteorological data......read more
Articles and Press Releases
Newsletter Articles
Privacy Policy Update
We've updated our privacy policy.Learn More