By using Campbell Scientific’s external line of cellular modules, system integrators, OEMs, and large end users can avoid costly, time-consuming maintenance visits to remote devices around the world.
The CELL200 series of external cellular modules are 4G LTE cellular devices that provide serial or CS I/O connectivity to a number of cellular networks, including Verizon, AT&T, T-Mobile USA, Rogers, Bell, Telstra, and Telus. The networking and carrier used by the CELL200 series is determined by the model used and the SIM card inserted into the device.
The CELL205 has very low power consumption when compared to other cellular modems: 14 mA at idle, 39 mA when active, and 300 µAwhen in low power mode.
When coupled with Campbell Scientific data services, these devices are ready for you to use out of the box. There is no need for you to work with cellular carriers for provisioning and experience the accompanying hassle.
The CELL205 is part of the CELL200 series of modems that includes:
Note:The CELL205 does not ship with a SIM card unless the cellular modem was provisioned with/for Campbell Scientific cellular data services; the SIM card is provided by the carrier when signing up for service. For more information, visit theCellular Data Services page.
Read MoreThe CELL205 is an industrial 4G LTE cellular module. It requires at least one micro-SIM 3FF card (for six position/contacts interface) supplied by your cellular carrier and a suitable 12 or 24 Vdc nominal power source. The CELL205 has an RS-232 serial port and a CS I/O port that can be used for serial server, serial client, and PPP host services. These ports are commonly connected to a data logger RS-232 serial or CS I/O port. The CELL205 has two antenna connectors to be used for primary and diversity antennas, although the unit can operate with only the primary cellular antenna connected.
The CELL205 provides Internet connectivity to any Campbell Scientific data logger located within range of a compatible cellular network. Armed with Internet connectivity, a data logger can remotely connect to Campbell Scientific software on a PC, mobile device, and the cloud. The CELL205 can also enable many data loggers to communicate using other Internet protocols, such as Modbus, DNP3, email, and web (HTTP).
The CELL205 provides highly reliable connectivity and remote device management independent of the device it is connected to. The numerous embedded services include IP serial server and client.
Campbell Scientific offers low-cost cellular data service plans for the CELL205. Our data service plans include Verizon in the United States and AT&T in North America (US, Mexico, Canada), as well as international access to over 600 carriers in 185 countries. TheKonect routing serviceis included to assure a secure connection with Campbell Scientific data logger support software.
The CELL205 is configured using a web-based configuration tool hosted by the cellular module. It can be accessed using Internet Explorer or Firefox remotely over the cellular WAN (when in serial server mode) or via USB.
The CELL205 can also be configured directly from the data logger when used in PPP mode (default mode) using theDevice Configuration Utilityor CRBasic instructions.
Data loggers can be connected in a variety of ways to suit the needs of the application. Common methods include the use of serial or CS I/O cables.
Compared to many other industrial cellular modules, the CELL205 has extremely low power consumption. The average current consumption at 12 Vdc is approximately 14 mA when idle, depending on its configuration. Additionally, the CELL205 can be turned on and off easily using a data logger SW12V port or theIPNetPower()instruction (PPP mode for the CR1000X, CR300, and CR6 only). When using the SW12V terminal, the modem can typically be powered with aBP12 battery, aCH150 charging regulator, and anSP10 solar panel.
Campbell Scientific offers three antennas for the CELL205. Our 4G/3G/2G 0 dBd cellular dipole whip antenna (pn 32256) connects directly to the CELL205 (no cable required) and can transmit short distances. Our higher gain omnidirectional (pn 18285) and Yagi (pn 31128) antennas require a cable to connect them to the CELL205. TheCOAXSMA-L cableconnects the antennas directly to the CELL205 cellular antenna connector. TheCOAXNTN-L cableand a surge protector (pn 31317) are used when the CELL205 is susceptible to lightning or electrostatic buildup or for long cable runs.
Transmission Distance or Area | Dependent upon antenna used and LTE, WCDMA, GSM EDGE, and GSM GPRS coverage. |
Certifications | IC (Industry Canada) 10224A-201611EC21A |
Host Interface |
|
RF Connectors | 2 SMA antenna connectors (primary and diversity) |
Operating Temperature Range | -40° to +80°C |
SIM Interface | 3FF (6 position/contacts) Supports SIMs that require 1.8 or 3 Vdc. |
Service Requirements | Network coverage at the data logger site and cellular data service plan. |
Dimensions | 13.46 x 8.1 x 2.86 cm (5.3 x 3.19 x 1.13 in.) |
Weight | 215.5 g (7.6 oz) |
Cellular WAN |
|
Network Technology | 4G LTE CAT-1 (with automatic fallback to 3G) |
Carrier Approval | AT&T, T-Mobile USA, Rogers |
LTE | 1900(B2), AWS(B4), 700(B12) |
WCDMA | 1900(B2), AWS(B4), 850(B5) |
Data Speeds |
|
LTE |
|
WCDMA |
|
GSM EDGE |
|
GSM GPRS |
|
RS-232 or CS I/O | 9600 bps to 460.8 kps |
Power Consumption |
|
Low Power Mode | 300 µA |
Idle | 14 mA |
Active | 39 mA |
Radio Output and Sensitivity |
|
Output Power |
|
Sensitivity Range | -99.5 to 110.5 dBm (10 M) |
Note:The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.
Product | Compatible | Note |
---|---|---|
CELLDATA(retired) |
Note:In serial server mode, a cellular account with a static IP address is required.
Data Logger Model | Connecting to CELL205 via CS I/O Port | Connecting to CELL205 via RS-232 Port (choose one) |
CR300 and CR310 |
N/A |
|
CR6 | 16675SC12 CS I/O cable |
|
CR1000X | 16675SC12 CS I/O cable (PPP and serial server) |
|
CR200(X) Series | N/A |
|
CR800 and CR850 |
16675SC12 CS I/O cable |
|
CR1000 and CR3000 |
16675SC12 CS I/O cable |
|
CR5000 | N/A |
|
CR510 and CR10X |
N/A |
|
CR510-PB and CR10X-PB |
16675SC12 CS I/O cable |
|
CR23X | N/A |
|
CR23X-PB | 16675SC12 CS I/O cable |
|
To update the CELL200 series operating system:
The update process can take 2 to 4 minutes.
Why Update?This OS resolves network registrations issues.
Three example programs as described in the CELL200-Series manual. ThePowerprogram shows how to control power to the CELL200 series by using the CRBasic
IPNetPower() instruction. TheSetSettingsexample shows how to set up the cellular module using the SetSetting() instruction. It also illustrates how to retrieve status information from the module in the CRBasic program. TheSettingsexample demonstrates using terminal commands.
We've updated our privacy policy.Learn More