The AVW216 is a vibrating-wire analyzer module that includes an internal 2.4 GHz spread-spectrum radio for wireless communication in many countries worldwide. With this vibrating-wire analyzer module, your data logger can measure vibrating-wire strain gages, pressure transducers, piezometers, tiltmeters, crackmeters, and load cells. These sensors are used in a wide variety of structural, hydrological, and geotechnical applications because of their stability, accuracy, and durability.
Read MorePurchase of this product is not recommended for new networks to be deployed in the European Union (EU) that may require future expansion. This and other RF-compatible products will not be available for sale in Europe after 01 Jan 2015 due to changes in EU legislation.
AVW216采用振动线谱分析技术(VSPERT®)。vspect.®observes the incoming sensor signal, performs a Fourier transform and a spectral analysis (transforming the time series into individual sinusoidal components in the frequency spectrum), and determines the sensor frequency by identifying the largest signal in the acceptable range while filtering out environmental and electrical noise.
The AVW216 analyzer module also provides many self-checking diagnostics such as vibrating-element signal strength, signal-to-noise ratio, vibrating-element signal decay ratio, and incorrect signal response. These diagnostics can be running in the background to give continual feedback of the condition for each sensor.
AVW216通常将其数据发送到连接到数据记录器的RF416扩频无线电。AVW216也可以直接连接到数据记录器。
-笔记- | Electrical specifications are valid over a -25° to +50°C range unless otherwise specified. Non-condensing environment required. |
Operating Temperature Range | -25°至+ 50°C |
Internal Radio Frequency Range | 2.450 to 2.482 GHz |
Radio Power | 50 mW |
测量的振动线传感器数量 | Up to 2 vibrating-wire sensors can be connected to the analyzer module. Additional sensors can be measured by using an AM16/32-series multiplexer. |
Power Requirements | 9.6到16 VDC |
模拟输入/输出 | 2 differential (DF) vibrating-wire measurements (V+ and V-) and 2 single-ended (SE) ratiometric resistive half-bridge measurements (T+ and T-) for vibrating-wire sensor's onboard temperature sensor. |
数字控制港口 | 3数字控制端口(C1 - C3)
|
RS-232端口 | 1 9引脚RS-232端口(用于连接数据记录器COM端口) |
测量分辨率 | 0.001 Hz RMS(±250 mV差分输入范围; -55°至+ 85°C) |
Measurement Accuracy | ±0.013%的读数(±250 mV差分输入范围; -55°至+ 85°C) |
输入电压范围 | 用于振动线输入的±250 mV(差速器) |
共同模式范围 | ±25 V |
Baud Rates | 可选择1200到38.4 kbps(ASCII协议是一个起始位,一个停止位,八个数据位,无奇偶校验。) |
Memory |
|
Dimensions | 21.6 x 11.18 x 3.18 cm (8.5 x 4.5 x 1.2 in.) |
Weight | 0.43千克(0.95磅) |
典型的电流排水@ 12 VDC |
|
静止,收音机关闭 | ~0.3 mA |
无线电徒刑循环1 | 〜3 mA(包括静态电流) |
Radio Always On | 〜26 mA(无线电传递电流100 mA) |
活动RS-232通信 | 〜6 mA(3秒在通信停止后,电流将下降到静态电流) |
Measurement | 〜25 mA(平均在2秒) |
Note:以下显示了显着的兼容性信息。它不是所有兼容或不兼容产品的全面列表。
Product | Compatible | Note |
---|---|---|
21X(retired) | ||
CR10(retired) | CR10仅支持SDI-12模式。 | |
CR1000.(retired) | ||
CR1000.X | ||
CR10X(retired) | CR10x仅支持SDI-12模式。 | |
CR200x.(retired) | ||
CR206X(retired) | ||
CR211x.(retired) | ||
CR216X(retired) | ||
CR23X(retired) | CR23x仅支持SDI-12模式。 | |
CR295x.(retired) | ||
CR3000(retired) | ||
CR500.(retired) | ||
CR500.0(retired) | The CR5000 supports the SDI-12 mode only. | |
CR510(retired) | ||
CR800 | ||
CR850 | ||
CR9000C.(retired) | ||
CR9000x.(retired) |
Product | Compatible | Note |
---|---|---|
ENC10 / 12. | 如果使用RS-232端口,则AVW216必须安装平板,以适合ENC10 / 12。 | |
ENC10 / 12.R | If using the RS-232 port, the AVW216 must be mounted flat to fit in an ENC10/12R. | |
ENC12/14 | 如果使用RS-232端口,则AVW216必须安装平板,以适合ENC12 / 14。 | |
enc14 / 16. | ||
enc16 / 18 | ||
enc24 / 30. | ||
enc24 / 30.S |
The AVW216 Vibrating-Wire Spectrum Analyzer Module allows our data loggers to measure vibrating-wire strain gages, pressure transducers, piezometers, tiltmeters, crackmeters, and load cells.
AVW216的内部扩频无线电可以将数据传输到其他AVW216分析仪模块,RF416扩频无线电和RF432扩频无线电。AVW216没有透明模式,因此其内部无线电不能与RF415无线电通信。
The AVW216 requires a desiccated, non-condensing environment. A Campbell Scientific enclosure is recommended when the analyzer module is in the field. The AVW216 has built-in keyhole flanges for mounting to an enclosure backplate.
AVW216通常由数据记录器的电源供电。
Current AVW200 firmware. Use the Device Configuration Utility version 1.13 or greater to send firmware and to configure the AVW200.
Number of FAQs related toAVW216:12
Expand All全部收缩
不可以。AVW206,AVW211或AVW216不能与其他AVW200系列模块通信。
The AVW200-series modules are not required, but they do reduce the chance of erroneous readings by filtering electrical noise that is sometimes present.
AVW200系列模块需要2秒,以从每个传感器获取测量值。AVW200系列模块维修两种AM16 / 32B多路复用器,每个都有16个振动线传感器,需要大约64秒获取数据。
两个可能的原因如下:
Yes, using a null modem cable.
Two multiplexers, each with a maximum of 16 or 32 sensors per multiplexer, can be attached. If temperature measurements are excluded from each sensor, 32 sensors are possible.
The AVW200 must be wired directly to the data logger via a cable.
AVW206,AVW2011和AVW216具有内置的扩频无线电,调谐到不同的频率,允许数据记录器通过适当的无线电链路与远程AVW设备通信。
We've updated our privacy policy.Learn More