The AL200 is an ALERT2 encoder and modulator that supports ALERT2 and ALERT-concentration services. It meets the ALERT2 standards maintained by National Hydrologic Warning Council (NHWC) and ALERT Users Group (AUG). ALERT2 improves the accuracy and performance of flood warning systems and software, by providing you with faster data transfer, forward error correction, and a TDMA architecture.
With integrated sensor inputs, the AL200 allows you to create a minimal ALERT2 transmitter/station, decreasing the cost of a typical flood warning system. Combining the AL200 with a Campbell Scientific data logger provides enhanced sensor support, user-defined logic and control, and data logging capabilities.
Note:开发了AL200嵌入式代码的一部分,并由Blue Water Design LLC版权所有,并根据许可使用。
Read MoreWhen used standalone, the AL200 can generate time and event driven reports for Battery, Clock Status, Tipping Bucket, Analog Input (mV or mA), Digital (SDI-12 or High/Low State).
Power Connector | Two-wire, 0.15-in. pitch removable terminal (reverse polarity protected) |
电源要求 | 9 to 18 Vdc |
配置 | Device Configuration Utility over USB (settable modulation levels using Device Configuration Utility) |
LED | GPS,串行,无线电(RS-232和CS I/O共享串行活动LED。) |
CS I/O Port | SDC 7, 8,10, or 11 (multiplexed with on-board sensor interface) |
RS-232端口 | DCE |
USB Port | micro-b |
温度范围 | -40°至 +60°C |
Communication Rate |
|
当前排水 |
|
Timekeeping Setting via GPS | ±1μs |
Drift | ±0.17 s/day (without GPS sync, 40°C temperature change) |
Analog Input (SE1) Sensor Interface | 0 to 5 Vdc (16-bit ADC; millivolt or 4 to 20 mA selectable) |
支持协议 | ALERT1 and ALERT2 |
SMA连接器 | Active GPS antenna |
Test Button | Test transmit and tone |
Dimensions | 16 x 7.7 x 2.2厘米(6.3 x 3.0 x 0.9英寸) |
Sensor Interface |
|
Channels Available | Switch closure (P1), single-ended analog (SE1), limited SDI-12 (C1), switched 12 V, ground |
Analog input (SE1) | 0 to 5 Vdc, 16-bit Adc (millivolt or 4 to 20 mA selectable) |
Radio Interface |
|
Channels Available | TX,PTT,开关电池,地面 |
RCFSK Modulation | 100至1000 mV,±50 mV(可选软件) |
标准 |
|
Compliance | RoHS and CE |
产品标准 | EN 61326-1:2013 |
测试标准 |
|
Note:以下显示了显着的兼容性信息。这不是所有兼容或不兼容产品的全面列表。
产品 | Compatible | Note |
---|---|---|
21x(retired) | ||
CR10(retired) | ||
CR1000(retired) | ||
CR1000X | ||
CR10X(retired) | ||
CR200X(retired) | ||
CR206X(retired) | ||
CR211X(retired) | ||
CR216X(retired) | ||
CR295X(retired) | ||
CR300 | ||
CR3000(retired) | ||
CR310 | ||
CR350 | ||
CR500(retired) | ||
CR5000(retired) | ||
CR510(retired) | ||
CR6 | ||
CR800 | ||
CR850 | ||
CR9000(retired) | ||
CR9000X(retired) |
AL200支持Alert1和Alert2协议。
A standalone AL200 can measure:
当前的AL200操作系统用于Alert2使用新版本Alert2 2.0 API。需要设备配置实用程序来更新AL200中的操作系统。
Current version includes bug fixes and aligns with the ALERT2 2.0 API. Information on the API commands supported can be found in the included pdf document. This firmware is not recommended for users using ALERT2XX systems or when using the AL200 in stand-alone mode.
Current AL200 operating system for ALERT and ALERT2. Requires the Device Configuration Utility to update the operating system in the AL200.
这些当前版本包括对其先前版本的错误修复和改进,并建议所有用户使用。
Operating System | Version |
ALERT | 1.0 |
警报2 | 4.0 |
A software utility used to configure the ALERT210 and AL200.
Windows操作系统的AL200 USB驱动程序。32和64位支持Windows 8,Windows 7,Windows Vista和Windows XP。
注意:在将AL200插入计算机之前,应加载驱动程序。
We've updated our privacy policy.Learn More